STEFFEN SYSTEMS CONVERSION SYSTEM (LARGE TO SMALL BALE) for sale POA

Hay Tools / Bale Choppers

steffen systems conversion system (large to small bale) 163363 001 steffen systems conversion system (large to small bale) 163363 002
steffen systems conversion system (large to small bale) 163363 003 steffen systems conversion system (large to small bale) 163363 004
steffen systems conversion system (large to small bale) 163363 005 steffen systems conversion system (large to small bale) 163363 006
steffen systems conversion system (large to small bale) 163363 007 steffen systems conversion system (large to small bale) 163363 008
steffen systems conversion system (large to small bale) 163363 009 steffen systems conversion system (large to small bale) 163363 010
steffen systems conversion system (large to small bale) 163363 011 steffen systems conversion system (large to small bale) 163363 012
steffen systems conversion system (large to small bale) 163363 013 steffen systems conversion system (large to small bale) 163363 014
CALL 03 8547 8478
Title STEFFEN SYSTEMS CONVERSION SYSTEM (LARGE TO SMALL BALE)
Make STEFFEN SYSTEMS
Price POA
Listing Type New
Stock Number CONVERSION
Refcode TA481449

The process starts with an automated feed table on which the loader operator places the incoming large bales. The machine accepts both 32" x 35" and 46" x 35" large bales. This table then advances the large bales into the cutter box which tilts them on their edge to allow for the proper cut. Once the bale has been sliced into sections of 16" x 35", the bottom slab is slid over, allowing the next slab to fall down behind.



These slabs are then pushed forward into the weigh chamber while the operator removes the old twines. Here the simple adjustable beam scale determines the proper amount of hay, which is sectioned off by the feed forks. At this time, the weighted slab is split and advanced onto the lift table. The lift table then raises the slab into the actual compression chamber. The main compression ram now applies pressure against the slab reducing its length to either 24" or 18" depending on the selection made for the finished bale length.



Once compressed, the eject cylinder forces the bale horizontally into the banding chamber. The bale is held with two steel plates, while the banding unit places bands transversely along its width. The number of bands is selectable, but normally would be six. Once this process is complete, the next bale extrudes the finished banded bale out and it expands to its finished length of 24" or 30", depending on the selection, then is fed into the secondary cutting box. This cutter slices the bales from one 16" x 36" into two 16" x 18" bales. After slicing, the bales are fed into the accumulation stacking table which groups them into proper configurations for mechanically handling into storage or onto a trailer.



The entire process happens in approximately 30 seconds with the standard machine, or 15 seconds with the higher power option. The power for this operation comes from an electric driven hydraulic power station consisting of multiple 30hp motors, each driving hydraulic pumps. The automation is controlled by a PLC (Programmable Logic Controller), with full operator manual overrides. All manual functions are protected by the PLC to prevent operator damage. All necessary guarding is supplied and safety shutdowns and lockout systems are integrated via the PLC.



Large Bale cutting system consists of:
» 9' wide x 16' long hydraulic powered automated feed table

» Twin cylinder tilting table to place bales on edge

» 6" x 114" 2500 psi rated cutting cylinder

» Two S-7 heat treated tool steel blades

» Cut slab unstacking system



Feed system consists of:
» Chain driven in-feed table to advance slab

» Operator station to remove old twines

» Weigh platform with manually adjusted weights

» Separation forks to split slab

» Lift table to raise weighed slab



Compression system consists of:
» 6" main ram rated to 2500 psi, rigid mounted

» 5" eject ram rated to 2500 psi, rigid mounted

» High strength steel banding plates

» Chamber sidewall is 1" steel plate

» Automated Strapak RQ8Y plastic banding unit



Finishing system consists of:
» Secondary slicer with 5" cylinder

» Secondary slicer blade heat treated S-7 tool steel

» Accumulation table with 24 bale capacity



Electronic system consists of:
» Twin Automation Direct D0-06 controller

» Fully fused systems

» Motor starters

» Fully automatic with full manual override



Hydraulic system consists of:
» Three 30hp electric motors

» 180 gallon reservoir

» High performance piston pumps operating at 2200 psi

» Relief valves

» Large capacity filtration system

» Air to oil large capacity cooler unit

The information contained within classified listings on TradeFarmMachinery.com.au is generated by the private and dealer advertisers. Please confirm listing details including price and specifications directly with the seller.

Related Articles

Kuhn delivers new VB round balers

Fast, simple and reliable are words agricultural equipment maker Kuhn uses to describe its eight new variable chamber round baler models +more

REVIEW: Hustler Chainless X5000 bale feeder

After three years of refinement, testing, and trialling on farms, the Hustler Chainless X5000 trailed bale feeder has been released. BRENT LILLEY was the lucky ducky sent to test it. +more

New Hustler chainless bale feeder arrives in Australia

New Zealand farm implement manufacturer Hustler Equipment has introduced its new Chainless X5000 bale feeder featuring a stronger drive system and rear-view camera to the Australian market. +more

CALL 03 8547 8478
Email Dealer
Dealer Address
Tenpack

Goornong, VIC, 3557
Australia