Mulchers, Reviews

Review: Cosmo Bully Mulcher

The Cosmo Bully BPF mulcher might be Italian made, but it's a well-built machine

The Cosmo Bully from behind
A rear roller leaves a tidy finish and helps control the height of the machine
Buy now

A mulcher can be one of the most widely-used pieces of machinery on a farm so long as it is strong and versatile enough to cope with cutting grass and tidying up prunings – and everything in between.

The Italian-designed Cosmo Bully range, built in India, has proven up to the job since it was launched in Australia some three years ago.

Hitching it up to a John Deere 6140M (definitely a bit of overkill for a 1.8-metre mulcher, but the most convenient tractor available), Farms & Farm Machinery see how the Cosmo Bully BPF 180 performed out in the field. Our test patch was some waste vegetable crop needing to be mulched and some rough grass around the edge of the field that needed topping.

 

CONSTRUCTION

The Cosmo BPF range of heavy-duty mulchers offers three models, from 1.8 metres to 2.25 metres wide. As with other Cosmo machinery I’ve seen, first impressions are of how well the machine is built, with plenty of thick folded steel plate used in the construction and tidy welding and finishing with shiny powder-coated Cosmo orange paint.

The unit hitches to the tractor with a sturdy headstock that uses CAT I or II linkage pins. There is a choice of either a fixed hole for the top link pin or a slotted hole to allow ground contour following.

Also built in where the mulcher mounts to the headstock are a hydraulic ram and slides. This allows the range to side shift up to 467mm, offsetting it to the side of the tractor for hard-to-reach spots.

Along the side of the machine are heavy-duty side skids to prevent the mulcher digging into the ground. Although these can be easily adjusted to set the height of the machine, there are only two positions, which might not be enough for some requirements.

Hinged steel plates along the front of the mulcher create a shroud, preventing objects from flying out and hitting the tractor.

the cosmo bully side on
The headstock allows 467mm of hydraulic sideshift

 

DRIVELINE

Power from the tractor comes through a heavy-duty drive shaft to the main centre gearbox. This is rated up to 100hp and the PTO input speed is 540rpm.

Inside the main gearbox is an internal freewheel clutch that prevents damage by allowing the rotor to freewheel when the power is disengaged.

Drive down the side of the machine to the rotor is through four XPB section belts, providing a safety mechanism to prevent damage to the gearbox and tractor if a solid object is struck.

It is great to see that although the belts are enclosed in a steel guard for safety, a slot in the centre makes it easy to check belt tension with a screwdriver, and it can be adjusted, if required, without removing the guard. 

 

ROTOR

The rotor is the business end of the machine and uses a balanced steel 170mm diameter drum. The 16 large cast iron inverted T-shaped flails are mounted to this. Bearings on each end of the rotor are enclosed inside the drum, which allows for the maximum cutting width and protects the bearings from any material that wraps around the drum.

The design of the flails lifts and then cuts the grass to ensure an even tidy finish. Rotor diameter from flail tip to tip is 410mm, which gives ample room for material to move through the machine. 

 

REAR HOOD AND ROLLER

Behind the flails is a row of adjustable steel rake tines used to hold the material in the machine until it is chopped to the desired size.

The length of the rakes is easily adjusted with a simple R clip and a series of holes on each one in place.

The rear hood, which holds the rake tines and encloses the rotor and flails, can be opened for easy access to clear blockages or safely replace flails. A large steel rear roller comes as standard on the machine. This helps to keep it following the ground and leaves a smooth tidy finish. It is also adjustable with two height settings. I’m happy to see that it has a scraper to keep it clean.

The Cosmo bully close up
Adjustable rake tines on the rear ensure material is chopped up before it leaves the machine

 

VERDICT

Overall, the Cosmo Bully BPF mulcher is a relatively simple but well-built machine.

I’m the first to admit I was a little sceptical, as I’ve seen some inferior imported product, but to give credit where credit is due, my fears were needless. There is plenty of steel where it is required and the level of finish is tidy.

It’s great to see that the drive belts on the side can easily be checked and tensioned with the safety cover still in place, as I’ve seen plenty of mulchers where it gets removed once and never put back on.

 

SPECS

Width: 2,000mm

Working width: 1,780mm

Weight: 680kg

Gearbox rating: 100hp

Power requirements: 60-100hp

PTO speed: 540rpm

Rotor shaft diameter: 170mm

Number of flails: 16

 

 

PLUSES

  • Hydraulic side shift
  • Main gearbox includes an internal freewheel clutch
  • Rear roller and rakes as standard
  • Belts can easily be checked and tensioned with guards in place

 

MINUSES

  • Limited height adjustment on skids and roller

Photography: Justin Bennett

Send this to a friend