FlipScreen transforms perceived unusable material into a valuable resource, helping farmers reuse soil and fertiliser while cutting costs and delivery delays
Most farms already have the gear to move material around. Loaders, skid steers, excavators – they do the heavy lifting every day.
The issue isn’t usually moving material, it’s dealing with it when it’s mixed, clumped, or inconsistent. That’s where a FlipScreen fits in.
A FlipScreen is an attachment that lets your machine screen and separate material on the spot. Instead of just shifting dirt, gravel, or fertiliser from one place to another, you can actually process it – take fines out, break up clumps, clean it up, and make it usable again.
They’re built to suit whatever machine you’re running. The hitch is designed to match your carrier, whether it’s a skid steer, loader, or excavator, so it fits properly and works as part of the machine.
Once it’s on, it runs off your hydraulics like any other attachment. You’re not locked into one job either as the screening panels can be swapped out depending on what you’re working with – finer screens for soil or fertiliser and larger apertures for gravel or rock. The same unit can also be used across different tasks without needing separate gear.
It’s not limited to just screening either. It still functions as a bucket, so you can dig, trench, and handle material normally, then process it as you go.
With the brush kit fitted, it will also keep working through wet or sticky material that would normally clog up and stop you.
It doesn’t change how you run your farm, it just gives you more control over the material you’re already handling.
Sitting on resources
Across Australian agricultural properties, the same pattern often repeats. A track wears out, it gets rebuilt, then it fails again. But the material itself hasn’t disappeared, it’s just sunk, mixed, and lost its structure.
Most of the time, you’re not short of material, you’re short of control over it.
With the ability to screen and separate that mixed layer, you can lift it, remove the fines, and put the usable aggregate straight back down properly – meaning the same material but a better result. It’s a shift from replacing roads to actually managing the material that makes them.
Most farms already have gravel pits, stockpiles, or old borrow areas sitting idle. They’re often ignored because the material is inconsistent, too dirty or too mixed to use properly.
Once it’s screened and sized, that ‘useless’ pile becomes a controlled supply for roads, drainage, pads, and general use.
In reality, a lot of farms are already sitting on their own small quarry without treating it like one.
Once that material is processed properly with FlipScreen, it stops being a liability and starts behaving like a resource.
Fertiliser pressure
Fertiliser isn’t what it used to be. With global conflicts affecting supply, especially of urea, availability has become unpredictable and prices have climbed.
What turns up isn’t always in good condition either. Moisture-affected fertiliser that’s clumped together often gets written off or spread unevenly, which wastes money and reduces effectiveness.
Screening breaks it back down into a usable form so every kilogram is applied properly. If supply tightens further, being able to process and mix alternative fertiliser sources on-site becomes more than just handy.
Manure, compost, and other blends already exist on most farms, they’re just underutilised because of inconsistency.
This is the kind of job FlipScreen was designed around – getting those materials back into a usable, consistent state is the difference.
There’s a long-standing habit of pushing unwanted material into a hole and moving on. Concrete, rock, and mixed rubble often get buried, but buried doesn’t mean gone, it just becomes a problem later down the track.
That same material can be reused for tracks, drainage, and base layers if it’s processed properly because it is not waste, it just hasn’t been refined yet.
Once it’s separated properly, that ‘waste’ becomes usable again, which is where FlipScreen turns a dead end into something productive.
Soil matters
Bringing in outside soil introduces risk, whether that is weeds, pests, or poor structure. Cleaning and reusing your own soil keeps things consistent because it already suits your land.
Screening removes rocks, roots, and debris, leaving something far more usable without the unknowns. Keeping everything on-site and under control only works if you can process it properly, which can be done effectively with a FlipScreen.
Dirty material doesn’t just affect the job, it affects your machines because rocks and debris cause wear, blockages, and unnecessary strain.
Cleaner material runs through equipment more smoothly and reduces that impact. The role FlipScreen plays in the process is taking that rubbish out before it hits your gear and changes how everything runs.
Time adds up
Waiting on deliveries, organising freight, and handling material multiple times all slow jobs down. Processing material on-site removes those delays and keeps things moving.
Jobs that would normally drag out can be completed much faster when everything is handled in one place.
When everything happens on-site in one pass thanks to FlipScreen, the whole job tightens up.
Supply chains often aren’t as reliable as they used to be, as costs change, availability shifts, and relying on external suppliers puts you at their mercy.
Being able to recover, separate, and reuse what’s already on your property gives farmers greater control over both timing and cost.
That level of control only comes from being able to process your own material, which is exactly where FlipScreen fits into the picture.
For more information, visit flipscreen.net
